Yamaha Motorcycle Brakes
Your brakes and braking system is one of the most important parts on your motorcycle. These parts are something you want to do inspections on for worn down and damage parts before every ride, to keep you and your bike safe.
If you are trying to get your motorcycle performing at its best, we have a large variety of Brake parts for you to choose from across many top brands such as Magura and Vesrah. Be sure to check out our selection of: Front master cylinders, OEM Type rear brakes, custom rear master cylinders, brake hoses and lines, OEM type brake hoses, Brake calipers 1977-1984, Brake calipers 1972-1976, Brake pads, Brake shoes, Brake switches, and Brake discs.
Fitment:
1972
1973
1974
1975
1976
1977
1978
1979
1980
1981
1982
1983
1984
-
Part #08-0255Master Cylinder Assembly - 13mm. bore (for single Front disc brake) Yamaha OEM type. Complete with brake lever, brake light switch, banjo bolt and banjo bolt washers (Pr.). Recommended for 1977-84 XS650's Mirror mount has left hand Threads.For single disc brake.Also fits RD250, RD350, RD400, XS750 Standard 1977-79, XS8... -
Part #08-0265Master Cylinder Assembly - 16mm bore.Recommended for late dual disc Front brakes on 1977-84 Yamaha XS650's Or single front disc brake (1972-76 650's). Yamaha OEM type. Complete with brake lever, brake light switch, banjo bolt and washers. Mirror mount has Left Threads.For dual disc brakes.Also fits: XS750 Standard and... -
Part #08-5001Brake Caliper - Complete Right side Brake Caliper assembly with mounting bolts and mounting bracket as shown (Brake pads not included).Fits to RH (stock single disc side) of 1977-84 XS650's The latest new production of the 1977-84 XS650 type Caliper.Note: These calipers are the same as earlier production except for th... -
Part #08-6008Early brake Caliper with pads assembly (72-76) Fits Right or Left side XS650OEM reference number: 306-25810-09-00Also fits: RD350 73 -
Part #08-600976 Type Single Master Cylinder 16mm Bore Mirror mount has Right hand Thread. #16-4662 (Black: RH Male to LH Female) will be needed to attach XS Type Replacement RH Mirror (16-3039) and the Right Hand (Brake Side) Mirror in the 16-3037 set.#16-4660 (Black: RH Male to RH Female) will be needed to maintain same height f... -
Part #29-0016Brake Caliper Rebuild Kit - Fits:1977-84 XS650 Front or Rear Calipers.Contains caliper piston seal, dust boot, spring clip and bleed screw rubber cap. OEM Ref.# 1J3-W0047, 1J3-20000-20-00Also fits: XS400 D/E/F 77-79 front and rear, SR500 E/F/G/H 78-81 front and rear, XS500 C/D/E 76-78 front and rear, XS750 77-79 rear... -
Part #29-0516Brake Caliper Piston - Fits: Front or Rear Caliper on 1977-84 650's. Replace if pitted or scored or air will seep into the brake system.Length = 41.3mm Bottom Width = 38.15mm Top Width = 27.26mm inside dementions = 5.5mm -
Part #29-3522Brake Pad Set ( for 1 caliper ) - Fits: Front - XS650 D-K (1977-84) or Rear - XS650 (1978-84) - Kevlar Carbon compound.OEM Ref.: 1J3-20000-11/13, 3H5-W0045-00, 2MO-W0046-01Also fit: SR500 1976-81, SR500 G/H 1980-81 front only, XS500 C/D/E 1976-78 front and rear, XS750 D/2D/E/F 1977-79 front and rear, XS750 SE/SF right... -
Part #30-3065High Performance Disc Brake Rotors for 77-84 XS650's Stainless Steel Disc - Drilled Fits: Front Right or Left - Less unsprung weight -Approx 3.6Lbs. verses stock discs at approx 6.2 Lbs. - 298mm.Dia. Japanese Made Superior Quality Performance Disc Brake Rotors.Includes two spacers. -
Part #08-0258Banjo Bolt Washers - 10mm. ((Pk/2) Fits: All Brake hoses & Banjo Bolts. d1 (internal diameter) = 10.0mm d2 (external diameter) = 15mm S (thickness) = 1.5mm -
Part #29-0500Brake bleed screw rubber cap. Fits majority of motorcycle bleed nipples -
Part #29-3211Rear Brake Shoes ( 2pc.set ) Fits: Rear wheel drum brake's on all 1970-84 XS/TX 650's Also compatible with:RD250 73-77, RD250 LC 80-82, RZ250 80-82, RD350 A/B 1973-75, RD350 LC 80-82, RZ350 80-82, RD400 1976-78, TX650 71-74, TX650 A 74-76, XS1, XS1b, XS2EBC equivalent 514 Vesrah equivalent VB-225 -
Part #12-0009Rear Brake Light Switch - Fits: All XS650's 1970-84.RD250, RD350, RD400, R5, DS7 1970-79 -
Part #08-0219Front Brake Master Cylinder Rebuild Kit - OEM # 535-W0041-60, 535-20000-60 Fits: Front Master Cylinder Assembly on All XS650 Models D-L (1977-84) with single front disc brake.Note: This Kit does Not fit earlier 650 models.Also Fits: XS360 C 76-79, XS400 77-81, SR500 78-82, XS500 76-78, -
Part #08-0251Magura Brake (RH) Master Cylinder Assembly 16mm. Replaces original types on All Yamaha XS650 and TX650's 1972-84. For front dual disc brakes 1977-84 Standard and Special, and single disc 1972-76.Compact lightweight design (10.3oz.), complete with brake switch, matching 10 x 1.0 Banjo Bolt and banjo bolt washers (2pc.)... -
Part #08-0253Magura 13mm Brake (RH) Master Cylinder. Genuine Magura, made in Germany.Replaces original types on single disc brakes Yamaha XS650 1977-84, Standard and Special.Compact lightweight design, complete with brake switch, matching 10 x 1.0 Banjo Bolt and banjo bolt washers (2pc.) Ideal for street tracker or custom build use... -
Part #08-0262Brake Side (RH side) Master Cylinder for use with single disc brakes as on 1977-84 Yamaha XS650's. All Alloy Low profile design Mirror mount has RH threads. Adapter 16-300112.9mm. Piston Dia., Banjo Bolt and brake switch Included.Also fits: XS750 1977-79, XS850 1980-81, XS1100 1978-81. For use as OEM: 1J3-25850-0... -
Part #08-3007Rubber Boot- Fits: 1972-76 Original Master Cylinders where the brake hose joins to the master cylinder. -
Part #08-4005Front Brake (RH side) Master Cylinder Replacement Lightweight (9.5oz.) Front Master Cylinder Assembly.Ideal for 77-84 Street Trackers or stock bikes with Single Disc brake.12.7.0mm. piston bore. Brake Light Switch and Banjo Bolt included.Reservoir has fluid level sight glass. Compact size.NOTE: This unit has an 8mm. mi... -
Part #08-5002Brake Calipers - Complete Right and Left Front Brake Caliper assemblies with mounting bolts and mounting brackets as shown (Brake pads not included).Convert your XS650 to Dual disc Brakes! The latest new production of the 1977-84 XS650 type Calipers.Note: These calipers are the same as earlier production except for the... -
Part #08-6006Yamaha Logo Round Yamaha disc brake badgeDiameter: 1.75 inches (4.5 cm)Fits: Caliper 08-6008 -
Part #19-0421Custom Stainless Braided Brakeline Kit TC Bros Choppers. 5 ft Brake line with two reusable 10 mm banjo fittings.Maxim operating pressure is 2500 PSI Easily cut to length to fit your application.Instruction included. -
Part #29-6504DOT/TUV approved Stainless Steel Braided Brake Line One Piece Upper/Lower Hose (41" Long) Fits: 77-84 XS650's Measure! Ends rotate up to 1 full turn. -
Part #29-6535Rear Brake Rod with end spring, adjuster Nut and lever Pin Fits: All Rear wheel drum brakes on 1970-84 XS/TX 650's -
Part #08-0204Front Brake Master Cylinder Rebuild Kit - OEM # 1J3-W0041-20 to fit optional Dual Disc on 1980 XS650SG - Master Cylinder - OEM# 2G2-25850-01 & 3J6-25850-00 XS650 Standard 1977-79, XS650 Special 1978-84.Note: This Master Cylinder is the same as used on 1979-81 XS1100 models with Dual Disc or offered as original on... -
Part #08-0217Rear Brake Master Cylinder Rebuild Kit - OEM# 1J3-W0042-50-00, 1J3-20000-50-00Fits: XS650SE/SF/SG (78-80) "Specials" with Rear master cylinder assembly.Fits: XS500 76-78, XS750 77-80, XS850 80-81. -
$46.96Part #08-0252Genuine Magura clutch perch. See brake side 08-0251 and 08-0253. -
Part #08-0257Banjo Bolt - M10. x 1.25 - Fits: All original XS650 and TX650 front & rear master cylinders and most Yamaha brake calipers. - OEM Ref.# 90401-10034 -
Part #08-3000Early type (1972-76) Dual Disc Brake Master Cylinder Assembly as used on European model XS650 TX 650's (22mm. Bore).Made by MikesXS for our European Distributors. Mirror mount has Left ThreadsMany XS650's in Australia are the European modelNote: NOT the same unit as the early Single Disc Brake type (16mm.) -
Part #08-4002Rear Master Cylinder assembly with reservoir for Custom or Race Bikes Bellcrank type action to operate (bellcrank lever is slotted with 8mm. hole).12.7mm. piston bore. 6mm. threaded Mount holes @ 45mm. center to center.Reservoir inlet rotates 340 degrees. Includes 10mm. x 1.25 outlet Banjo Bolt -
Part #08-4003Replacement Lightweight (11.1oz.) Front Master Cylinder Assembly Ideal for 1977-84 Street Trackers or stock bikes with Single Disc brake.11.0mm. piston bore. Brake Light Switch and Banjo Bolt included.This master cylinder is not intended as a replacement for the original; mirror mount is 8mm.RH. thread must use adapter... -
Part #08-4004Replacement Front Master Cylinder assembly with sloped reservoir for bikes with bars that situate the master cylinder on a slope - "Specials".14.0mm. piston bore. Brake Light Switch and Banjo Bolt included.NOTE: This unit does NOT have a mirror mount hole. -
Part #08-4008OEM Type Rear Master Cylinder Assembly for 1978-80 XS 650 "Specials"with rear disc brake. Includes plunger rod. -
Part #08-5000Brake Caliper - Complete Left side Brake Caliper assembly with mounting bolts and mounting bracket as shown (Brake pads not included).Fits to LH side of 1977-84 XS650's for conversion to Dual disc brakes (RH single disc is stock on 77-84 650's). The latest new production of the 1977-84 XS650 type Caliper.Note: These ca... -
Part #08-6007Caliper Brake Pad ShimYamaha XS650, XS400 -
Part #16-3001Mirror Adaptor Set - 10mm. Adaptor for Left hand threads, allows use of all conventional mirrors on Yamaha's (All Yamaha's have a Left Hand thread mirror stem on one side). -
Part #29-0017Rubber caliper sleeve Boot. - Boot allows caliper to float on mounting bolt sleeve.Once this rubber age hardens the caliper will not float and it should be replaced or brakes will drag or squeal. Polish the sleeve and install Boot to restore correct caliper float. Caliper Boot Fits: 1977-84 XS650 Calipers. Also fits: X... -
Part #29-0019Brake caliper Rebuild Kit - Fits: XS2/TX650/TX650A/XS650B/C (72-76) calipers.This 5pc. Seal kit rebuilds 1 caliper. -
Part #29-0501Caliper Bleed Screw - Standard type - Fits: 77-84 650's Front or Rear. M8 x 1.25 thread. 30mm overall length -
Part #29-0503Caliper Speed Bleed Screw - Built in check valve allows Easier brake bleeding.Fits: 1977-84 XS650 calipers. M8 x 1.25 thread, Overall length 1.10in. (28mm) -
Part #29-0518Brake caliper Piston - Fits: Front caliper on XS2/TX650/TX650A/XS650B/C (1972-76). Two pistons are used in these early calipers. Caliper pistons should be replaced if pitted or scored or air will seep into the brake system. -
Part #29-3200Brake shim kit. Fits XS650 front 1977-84, rear 1978-84. Specials and Standards.Reference # 4K0-W0045-02-00, Brake shim replaces original Yamaha worn out or missing brake pad mounting kit, Screw and shim.Also Fits: SR500 76-81, SR500 G/H 80-81 front only, XS500 C/D/E 76-78 front and rear, XS750 D/2D/E/F 77-79 front and... -
Part #29-3508Brake Pad Set - Front ( for 1 caliper ) - Round style with key tab. 48 x 8.8mm. Fits: XS650 B/C (1975-76), TX650 A (1973-76), & some XS2 (1972). Replaces OEM # 306-25811-05, 1A1-W0045. Kevlar Carbon Compound.Also works with most: RD250 73-77, RD350 74-75, RD400 76-78, TX500 73-75, XS500 75, TX750 73-76 -
Part #29-3620Brake Pad set Vesrah performance brand, made in Japan. Vesrah VD-205Brake Pad Set ( for 1 caliper ) - Fits: Front - XS650 D-K (1977-84) and Rear - XS650 (1978-84 - Resin compound.OEM Ref.: 1J3-20000-11/13, 3H5-W0045-00, 2MO-W0046-01XS250 C 77, XS250 DE F,G 79-880, XS360 76-77, XS400 E, F 78-79, SR500 76-81, SR500 E/F 7... -
Part #29-6507DOT/TUV approved Stainless Steel Braided Brake Line Fits: 77-84 XS650 Upper or Lower Front approximately 20" Long.Ends rotate up to 1 full turn. -
Part #29-6508DOT/TUV approved Stainless Steel Braided Brake Line Fits: 78-80 XS650 Rear Disc Brake approximately 24.5" Long.Ends rotate up to 1 full turn. -
Part #29-6517Brake Hose - Upper - XS2 (1972), TX650 (1973) Stock rubber type with protective spring. DOT Approved - 17-1/4" long, male threaded on one end and 20 degree fitting on opposite end of hose. -
Part #29-6522Brake Hose - Lower Front. Fits:1977-84 XS650's - Original Equipment rubber type - DOT Approved - Stock length 20" with 10 degree ends - Made in Japan