Yamaha Motorcycle Screws

Clutch Push Screw & Housing Assembly Kit.Kit contains: Push Screw Housing with mount screws, Push Screw with Adjuster and locknut, Return spring and anchor pin, Cable Hook with hinge pin. Push screw has Long type actuator arm that gives maximum leverage and provides lightest clutch lever pull. Fits: 1972-84 650's... 

Clutch Spring Screw - Sold Each. - 6 Pieces used per engine. Order what you need. Fits: All 1970-84 XS/TX650's. 

Lower Engine Case Stainless Screw Set. - 18pc. - Fits: Lower right hand & left hand engine cases on all 650's. 

Chrome Point Cover Screw 

Stainless steel socket head screws for carb holders Set of 4 for stock carb holders as used on 1970-84 XS650 's, XS400 's 

Advance/Breaker Housing Screw & washer Pk/6 (12pcs) - 6 countersunk flat-head type screws and 6 matching starlock washers. 2 sets required to do both engine housings on each engine. Fits: All 650's 1970-84 

Throttle Butterfly Shaft Screws (Pk./4)Fits: Stock Mikuni BS34/BS38 CV Carbs. All OEM XS1/XS2/XS650/TX650 carbs XS400 

Float Bowl Screws - 4mm. - ( Pk./4 Screws with lockwashers). Fits: Early Mikuni CV carb float bowls. 

Screws - 5mm.(no lock washers) Late Mikuni CV carb Lid Screw - Pk./4 

Screws - 5mm.- Early Mikuni BS38 CV carb Lid Screws with lockwashers and Late 34mm CV Bowl Screw Pk./4 

Stainless Steel carb link bar Screws - Set of 4 with socket (Allen) heads.Link bar screws hold carbs together (on the carb support brackets) and often need replacing when changing the fuel line T on stock 80-84 BS34 CV carbs.6mm x 13mm x 1.0 pitch 

Float Bowl Drain Screw with O-Ring - Fits: 80-84 Stock 34mm. Mikuni CV Carbs. 

Clutch Spring Screw Set - 12pc. - 6 socket head bolts with matching sleeves.Fits: 1970-84 Clutch hub. 

Alternator Housing Mount Screws - Special 6mm. (pk/2) Screws to mount alternator stator housing to engine.Fits: All 650's. 

Contact breaker plate Screws (2pc.) and flat Washers (2pc.) - Set for main backing plate adjustment.Fits: XS650, RD250, RD350, RD400 

Air Pilot Mixture Screw - (584 type) Fits: XS650C/D (1976-77) Stock Mikuni BS38 CV Carburetors. 

Fuel Idle Mixture Screw with O-Ring Fits: XS650E/SE/F/SF/2F(1978-79) Stock Mikuni BS38 CV Carbs. Beware!Carb idle mixture screw O-Rings included may or may not fit correctly in your Mikuni BS38 CV stock carburetor. The O-Ring in the carb as originally supplied by Mikuni/Yamaha varies in fit and size and we have found... 

Screws (Pk/2) for carb Top (Slide) Cover.Fits: Flatslide PWK 32mm XS Performance Carburetor 48-9010 

Screw Set (Pk/2) to fasten Float Bowl.Phillips Head 4mm. x M0.7 x 14mm. longFits: Flatslide PWK 32mm. xs Performance Carb 48-9010 

Chrome Allen Socket Screw Intake manifold screws 24 x 5mm 

Chrome Plated Screw M5 x .8 x 2 10 (Pk/10) 

5mm Screw for Gas Cap 

Bleed Screw for calipers. M8 x 1.25 thread, overall length 26mm (1.02") 

Chrome Switch housing Screws (Pk./2)for Clutch side handlebar switch.Holds switch halves together. Fits: 1972-84 650'sNOTE:These are replacement screws normally included with switch #24-2062 & #24-2063 

Chrome Switch housing Screws (Pk./2)for Brake (throttle) side handlebar switch.Holds switch halves together. Fits: 1972-84 650'sNOTE:These are replacement screws normally included with switch #24-2062 & #24-2063 

Black Switch housing Screws (Pk./2)For Brake (throttle) side handlebar switch.Holds switch halves together. Fits: 1972-84 650'sNOTE:These are replacement screws, normally included with switch #24-2059 & #24-2060 

Black Switch housing Screws (Pk./2)For Clutch side handlebar switch.Holds switch halves together. Fits: 1972-84 650'sNOTE:These are replacement screws normally included with switch #24-2058 

Lens Screws (Pk./2) - For 11-2186 signal lamps. 3x18mm 

8mm. x 55mm. long Signal Lamp Stud 

Lens Screws - (Pk./3) Fits: Round type XS tail lights. 

Lens Screws - (Pk./2) Fits: Short Rectangular Type XS tail lights. 

Lens Screws (Pk./2) - Fits: Long Rectangular Type XS tail lights. 

25 pack Phillips Carburetor Float Bowl Screws 4x14 . Used on many Mikuni VM carbs from the 70's.Yellow Zinc Coated Steel. JIS Philips cross-head machine screws assembled with captive spring washer. Pitch = 0.7mmhead diameter (dk) = 7mm head height (k) = 2.6mmlength (L) = 14mm