TX500 TX750 Twins

Engine Tachometer Drive Oil Seal OEM Seal #93104-07036 Ars SO 7-13-4 HS Fits the following Yamaha models: TX500  XS500  XS1 XS2 TX650 XS650 XS750 XS850 

Motion Pro Clear Fuel Line - 1/8" Internal Diameter- 1/4" Outside Diameter. Priced per foot - can be used for float bowl overflow hose. carb sync gauge hose 

Stainless Steel Engine Cover Bolt Set includes: 55 bolts and 3 Allen keys for a total of 58 pieces.These bolts are all SMOOTH head Allen bolts. We polish the bolts for 24-48 hours in a tumbler to get a bright even look. Primarily all visible bolts on lower covers - includes the bolts for: Cylinder Head Cover- LH Cove... 

Daiichi brand replaces NIPPONDENSO Condensors. Equivalent to OEM: 1L9-81625-50-00 371-81625-10-00 Condenser; Yamaha: XS360C/D/2D - (76-77) XS400D/E/2E/F/2F - (77-79) TX500/A - (73-74) XS500B/C/D/E (75-78)  

This impact resistant graduated tank takes the place of the original gas tank while performing carb synchronizing. Includes four feet of 1/4" fuel line and an inline brass petcock. Suggestion: look for a used hospital or doctors office IV stand.  These come with 4 or 5 wheels on a weighted base, telescoping stand... 

Allows removal of internal snap rings used in hydraulic master cylinders Replaces Honda# 07914-SA50001 Can be used to remove and replace small to medium internal snap rings up to 50 deep- including those used for transmission gear locating- bearing retention- and oil seal retention Applicable to some fork seal retainin... 

OEM: 2411 10% discount on orders of 10 spark plugs or more- 14mm thread. NGK plugs provide a reliable spark. If you need a hotter running plug select B7ES or a colder running plug select B9ES plugs.  Standard plugs on the following motorcycles: MAKE YEAR ENGINE CLASS MODEL HONDA 1968-1972 3... 

OEM: 2120 10% discount on orders of 10 spark plugs or more 12mm thread. NGK plugs provide a reliable spark. If you need a hotter running plug select D7EA or a colder running plug select D9EA plugs.  Standard plugs on the following motorcycles: MAKE YEAR ENGINE CLASS MODEL HONDA 1972-1974 3... 

OEM: 2420 10% discount on orders of 10 spark plugs or more 12mm thread. NGK plugs provide a reliable spark. If you need a hotter running plug select D8EA plugs.  MAKE YEAR ENGINE CLASS MODEL HONDA 1980-1981 900 CB900C HONDA 1981 900 CB900F KAWASAKI 1981-1982 305 KZ305-A... 

NGK Stock Number 8051, LD05F Black NGK 5k Ohm Resistor Plug Cap. 90 degree elbow - for 14mm thread spark plugs with terminal stud. Rubber waterproof boot to seal out the elements. Make Model Year Model KAWASAKI 1980-1984 KZ550 KAWASAKI 1984-1985 ZX550 YAMAHA 1973-1974 TX500 YAMAHA... 

NGK Stock Number 8072, XD05F Black NGK 5k ohm resistor plug cap. 102 degree elbow, long style - for 12mm or 10mm thread spark plugs with terminal stud. Rubber waterproof boot to seal out the elements.   Please note - some models take two types of plug caps.  The following table shows what was fitted to your... 

JT Sprocket 16T Front Sprocket for 530 chain Stock tooth count for the XS500C 1976-1977 with alloy wheels One tooth smaller for the 1972-1983 TX650/XS650 and 1974-1975 XS500A/B with wire wheels. 

Motion Pro Clear Fuel Line - 1/8" Internal Diameter- 1/4" Outside Diameter. 25 foot Roll.  This hose can be used for float bowl overflow hose, carb sync gauge hose or petcock vacuum hose. 

Set of three high quality JIS Screwdrivers - Chrome Vanadium with Magnetic tips. Guaranteed for life. #1- #2 & #3 sizes. "full tang" - meaning that they are a one piece shaft from tip to tip with a hex bolster end. Every screw on every Japanese designed motorcycle from the 1950s right up to the newest bikes in th... 

Tappet Feeler Gauges - .006 - .008 inch - Individual Allows accurate tappet adjustments Angled blade for easy access to tappets Makes valve adjustments quick and easy Made in the U.S.A. 

Tappet Feeler Gauges - .002 - .003 inch - Individual Allows accurate tappet adjustments Angled blade for easy access to tappets Makes valve adjustments quick and easy Made in the U.S.A. 

Tappet Feeler Gauges - .004 - .005 inch - Individual Allows accurate tappet adjustments Angled blade for easy access to tappets Makes valve adjustments quick and easy Made in the U.S.A. 

Mirrors - Bar-End - pair (2) universal 80mm diameter w/convex mirror with adjustable stem for both steel and aluminum 7/8" bars. Matte Black Finish. Installation tip: These mirrors entail a 4-finger expander sleeve that expands as the socket head bolt is tightened. (See photo) As the sleeve expands- it bites into the... 

MC25 This versatile stand is easily adjustable to accommodate the wide range of engine types in service today. Height and width are both adjustable on the MC25- another major feature is the ability to rotate an engine a full 360 degrees. Pan removal- transmissions- starters- and clutches are just a few of the services... 

Gasket Cement - 1184 3-Bond #4 (Yamabond #4) - 100gram tube Gray semi-drying type. Use on gaskets except head gasket and on all surfaces without gaskets - excellent for crankcases. Three-Bond released 1184 as a replacement for 1104 and 1194. AKA Yama-Bond 

NGK Stock Number 8020, LB05EP Black NGK 5k Ohm Resistor Plug Cap. 90 degree elbow - for 14mm thread spark plugs with solid terminal (usually found on Champion spark plugs) or a terminal nut. Rubber waterproof boot to seal out the elements. Same as LB05E except with a slightly longer rubber boot. Fits HOND... 

Bronze Swing arm Bushings (Set/2) - Replace your plastic, steel or bronze factory swing arm bushings and improve your bikes handling.  Equivalent to OEM: 33033-009 90386-22029-00. Bronze. Fits Kawasaki Z1 KZ900 KZ750B1/B2/B3/B4 H2B/C KZ650B1/C1 KH500 H1B/E/F KH400 S3 KZ400A1/A2/D/S S1B/C S2 KZ250 KH250 KE250... 

Inhibits rust, leaks, and corrosion. Not affected by oils, chemicals, solvents, etc. Low strength: frequent removal. 

Inhibits rust, leaks, and corrosion. Not affected by oils, chemicals, solvents, etc. Medium strength: bearing and stud. 

Feeler Gauge Set- Metric Feeler Gauge Set for setting valve clearances.9 pc. Set (marked in metric sizes only). 0.04mm. - (.0015")0.05mm. - (.002")0.06mm. - (.0025")0.07mm. - (.0028")0.08mm. - (.003")0.10mm. - (.004")0.15mm. - (.006")0.20mm. - (.008")0.30mm. - (.012") 

Feeler Gauge Set- Metric Feeler Gauge Set for setting valve and contact point clearances. 20pc. Set (marked in metric sizes only).0.05mm. - (.002") 0.55mm. - (0.22")0.10mm. - (.004") 0.60mm. - (0.24")0.15mm. - (.006") 0.65mm. - (0.26")0.20mm. - (.008") 0.70mm. - (0.28")0.25mm. - (.010") 0.75mm. - (0.30"... 

Feeler Gauge Set - Metric/Inch Feeler Gauge Set for setting valve and contact point clearances. 32pc. Set (marked in metric and inch sizes).0.03mm. - (.001") 0.04mm. - (.0015") 0.05mm. - (.002") 0.06mm. - (.0025")0.07mm. - (.0028") 0.08mm. - (.003") 0.09mm. - (.0035") 0.10mm. - (.004")0.13mm. - (... 

Electrical Continuity Tester (use with power off) - Detects open circuit in fuses,diodes, switches, sockets and wires (requires one AA battery - Not included).Long 48" leads. 

Vise type tool will hold inner clutch hubs- gears- sprockets and flywheels (using pins opposite jaws side). Carbon Steel with heat treated jaws and nickel finsih. Max 130mm (5") jaw opening. Keywords: holder clamp grip 

Choke Plunger Dust Seal - equivalent to OEM 306-14173-00-00:  1970-1979 XS650 BS38 CV Carb Choke Plunger.   1976-1977 XS360 1976-1977 XS500 1973-1974 TX750 1977 XS750 1981-1982 XJ550 

Clutch Friction Plate - Sold EACH Fits: XS360 1976-1977 XS400 1977-1982 not for 1982 XS400J or XS400RJ XS500 1975-1978 TX500 1973-1974 XS750 1978-1979 XJ550 1981-1983 XJ650 1980-1983 XJ700 1984-1984 XJ750 1981-1983 FJ600 1984-1985 FZ600 FZ750 FZR1000 RD350 and RD400 builders also use these plates. M... 

Steering Bearing 25 x 48 x 15.2mm- 30 x 48 x 15mm Fits Yamaha TX500 1973-75- XS500 1976-78- XZ550 1982-83- FZ600 1986-88- SRX600 1986- TX650 1970-76- XJ650 1980-83- XS650 1977-83- TX750 1973-74- XJ750 1981-83- XV750 1981-83- XV920 1981-83. 

Points & condensers - fits Yamaha TX500/A (73-74) XS500B/C/D/E (75-78) 

Useful tool for cleaning carb and carb jet orifices, master cylinder return holes, welder tips- etc. Assortment of different gauge wire tips. 

Adjustable oil seal puller with two tips- Head adjusts to 5 positions works well removing fork seals and other deep set seals. No more battling trying to remove stubborn seals - those hard to reach fork seals are no match for this tool 

The ultimate carb rebuild kit from Keyster.  For Yamaha TX500.  Two (2) kits are required to service a set of carbs. These kits contain parts not normally available - and help solve rough running issues related to these TX500 carbs. Included in the kit are: 4 x different Jet Needles - Lean, Standard (302...