Yamaha XS650 Bolts

Banjo Bolt Washers - 10mm. ((Pk/2) Fits: All Brake hoses & Banjo Bolts. 

Exhaust Studs for Cylinder Head - 10mm. x M1.25 x 43mm. Long with plated finish.Fits All 650's 1972-84 

Cylinder Head Stud for 3 hole Tappet Cover - 6mm. x M1.0 x 30mm. with plated finish. Fits Cylinder Head 3 hole Tappet covers on all 1970-84 650's. 

Steering Head Bolt with domed head and matching chrome radiused Washer.Fits: All XS650's with a steering head post Bolt (not models with a damper).Improved appearance over stock style. 

Oil delivery tube Banjo Bolt - attaches delivery pipe to cylinder head. - Chrome Plated. Fits: All 1970-84 650's - Sold as a Set of 2 only. 

Sidestand Bolt, Washer & Lock Tab - Fits: 1977-84 XS650 sidestand mount. 

Bolt assembly (Special type) - Fits: Brake Shoe Backing plate to Brake stay.Fits: All 1974-84 XS/TX650's. 

Bolts for Rear Sprockets - Original type (6pc. Set).Fits: All 650 Rear sprockets 1970-84 

Damper retaining bolts. Fits into lower fork leg to inner fork damper. Special size allen socket head. Fits: XS650's 1977-84 

Banjo Bolt - M10. x 1.25 - Fits: All original XS650 and TX650 front & rear master cylinders and most Yamaha brake calipers. - OEM Ref.# 90401-10034 

Crankcase Top Bolt Position (#4) Crankcase Top Bolt Position (#2)(Pk/10) 

Cylinder Head Bolt Set - 3pc. Bolt Set with chrome Domed Heads .1pc. 6mm. bolt (center at rear of cylinder head) + 2pc. of Head Bolts (2 outer bolts located under each spark plug). Fits: All 650's 1970-84. 

Engine Crankcase Bolts (Set4). Bolts fasten engine cases together and pass thru cases from the top of the rear portion of the engine. We have replicated the early type attractive Chrome plated Domed head type Bolts and have the 3 sizes in a set of 4. Set Fits: All 650's 1970-84. 

Bolt 10mm x 50mm x m1.25 with 17 Hexhead 

Tube Spacer: 19mm OD x 12mm ID x 32mm Long Spacer for Exhaust System 

Coil Standoff for #17-6903 30mm x 6mm I.D. 

Coil Standoff for Green coil 17mm x 6mm I.D.Can be used to adapt/install ignition coils to various motorcycles 

Coil Standoffs 10mm x 6mm I.D.Can be used to adapt/install ignition coils to various motorcycles 

Coil Standoffs 45mm x 6mm I.D.Can be used to adapt/install ignition coils to various motorcycles 

Threaded adaptor (Male thread) - Replacement stock adaptor as used on 70-84 XS650's. The cable end threads on to this piece at the engine drive end and we offer this as a replacement for damaged or lost adaptors. 

Bolt - Special Bolt that holds the Tach Drive into the Clutch (RH Engine) Case.Fits: All 650's 1970-84 

Bolt Set(4) with Lockwashers(4) to mount the front fender to the front forks.Fits: 78-84 "Special" model front fenders. 

Special Fine thread metric Bolt that passes thru Passenger pegs, thru frame and into muffler mountings (pk./2 bolts with lock washers) of stock OEM mufflers.Fits: XS1, XS1b, XS2, TX650 (1970-73). 

Crankcase Top Bolt Position (#2) (Pk/10) 

Crankcase Top Bolts 1 & 3 (Pk/10) 

Special 7mm. Bolts (Replacements/Spares) to fasten the cam sprocket to the camshaft on our XS performance Cams.OEM reference # 90105-07004-00 Bolts (not cam 05-0025) compatible with: XS400 (2) FJ1100-1200 (2) XS1100 (2) FJ600 (2) XJ400 (2) VMX12-13 (8) XJ550 (2)... 

Banjo Bolt - M10 x 1.0 for use on Magura master cylinder only. 

Replacement Socket Head Bolt Set - (Pk/2)Fits: Housing on XS Performance Heiden Filter cooler #15-6505 

Center Stand Bolt - Stainless Steel bolt - ported to put grease directly to pivot points where its needed and make the bike easier to pull up on the center stand. 

Sidestand Shoulder Bolt with Castle Nut Fits: All 1970-76 XS/TX 650's. 

Long Carb Holder bolts for PWK Manifold thru Carb holder ( Pk/4 ).Stainless Steel socket head type screws.Fits: Flatslide PWK 32mm. XS Performance Carburetor Set for XS650 48-9010Kit requires 2 Pks. of 2. 

Drain Plug for Float BowlFits: Flatslide PWK 32mm. XS Performance Carburetor 48-9010 

Chrome Rocker Shaft Plug 

Chrome Cylinder Guide Bar Bolt (Pk./2) Bolt Passes thru cylinder guide bar nuts located at Front/center of cylinder casting and secures cam chain guide bar to cylinder casting (inside cam chain tunnel). Fits: All 650's 1970-84 

Cylinder Head Stud for 4 hole Tappet Cover - 8mm. x M1.25 x 30mm. with plated finish. Fits Cylinder Head 4 hole Tappet covers on all 1972-84 650's. 

Bolt - Fastens stock XS650 headpipe lower flange to frame.10mm. x M1.25 x 20mm. with 17mm. hex head 

Rear Cylinder Head Bolt 6mm x 35mm Pk/10 

Headbolt (Outer) 8mm x 1.25 (Pk/10) 

Bolt XS1/2 Muffler to Late Frame. 12 x 1.25 x 30mm thread length, 19mm head.