Mikes XS

Haynes Manual SR500, XT500, TT500, 1975 to 1981.

Clear instructions and hundreds of photographs to help you perform anything from simple maintenance to basic repairs. Includes: Routine maintenance, Tune-up procedures, Engine, Clutch and Transmission Repair, Fuel and Exhaust, Ignition and Electrical, Brakes and Wheels, Steering, Suspension and Drive, Frame and Bodywork, Wiring Diagrams.

Mikuni Pocket Tuner. A handy pocket-size calculator which can be used to determine required jetting changes in Mikuni carburetors due to climate and temperature changes. The Pocket Tuner is applicable to both single and multi-carb applications on two-stroke and four-stroke engines. It also has a guide for determining rich or lean carburetor conditions.

For Mikuni Tuning Manual see 35-0665.

Mikuni carburetor Tuning Manual from Sudco. 92 page manual includes exploded parts views, parts listings and optional parts. Guides you through tuning and trouble shooting for the popular lines of Mikuni carburetors. The definite reference for Mikuni carburetors and a must for the do-it-yourselfer.

For Mikuni Pocket Tuner, see 48-8106.

Carburetor Holder SR500 E/F/G/H 1978-81. Replace your worn and cracked carb holders. Includes one carb holder and one intake gasket. Also fits: TT500 C/D/E/F/G/H 1976-81, XS500 1976-81, XT500 C/D/E/F/G/H 1976-81

OEM Reference #
• 583-13565-01-00

Float Needle SR500 1978-81

Also fits: XT500 1978-81

Front Wheel Bearing - 6303-2RS Nachi ball bearing (with 2 synthetic shields) Made in Japan - Highest Quality Fits: RD350 A/B 73-75, RD400 76-78, SR500 78-84, XV535 87-01, XV535S 96-97, TX650 A 74, XS650 75-83, XVS650 98-06, XS750 78080, XS850 80-81, TDM850 91-99, XS1100 78-81

OEM Reference #
• 93306-30317-00

Front Wheel Bearing Kit
Includes: (2) 6303-2RS Nachi ball bearing (with synthetic shields), (1) Front wheel Oil Seal - (SD-28-47-7), (1) Front Wheel Oil Seal - Speedo drive side - (SDO-45-56-6)

Made in Japan - Highest Quality - make sure any you are comparing are made in Japan and same quality.

Fits:

RD350 A/B 1973-75, RD400 1976-78, SR500 1978-84, XV535 1987-01, XV535 SE 88, XV535 S 1996-97, TX650 A 1974, XS650 1975-83, XVS650 98-06, XS750 1978-80, XS850 1980-81, TDM850 91-99, XS1100 1978-81

Front wheel Oil Seal - (SD-28-47-7) Fits: Front on All 650's 1973-84, RD350 A/B 73-75, RD400 76-78, SR500 78-84, XVS535 87-01, XVS535S 96-97, TX650A 74, XVS650 98-06, XS750 78-80, XS850 80-81, TDM850 91-99, XS1100 78-81

OEM Reference #
• 93102-28022

Front Wheel Oil Seal - Speedo drive side - (SDO-45-56-6). Fits: Front on All 650's 1973-84, RD350 A/B 73-75, RD400 76-78, SR500 78-84, XVS535 87-01, XVS535S 96-97, TX650A 74, XVS650 98-06, XS750 78-80, XS850 80-81, TDM850 91-99, XS1100 78-81

OEM Reference #
• 93105-45017

Float Bowl Gasket. SR500. Sold each.

Carburetor Repair Kit. SR500

OEM Reference #
• 2H0-14190-28
• 2H0-14184-00
• 583-14536-00
• 2H0-14198-00

Steering Bearing Set. SR500+

Fork Seal Kit.

Fits: RD400 1978-79, SR500 1978-93, XS650 D/E/F/G/H 1977-81, XS650 S E/F/G/H/J/K 1978-83, XS650 SE 1980-81, TX750 1973-74

Made in Japan

Single spring

Engine Oil Seal Kit. 10 pieces. Made in Japan.

Fits: SR500 1980-82, XT500 G/H 1980-81

Muffler Connecting Gasket SR500. Made in Japan. SR500 1978-82, 1987-88, 1991-92

OEM Reference #
• 2J2-14714-00

Speedometer Cable (Black) - Fits: XS650B-K (1975-84) and TX650A (1974) OEM# 341-83550-01 Made in Japan Also fits: SR500 78-84, XS500

OEM Reference #
• 341-83550-00
• 16M-83350-01-00

Tachometer Cable SR500 Fits: SR500 1978-83 1984-89 1991-99, XT250 1982 23"" Long

OEM Reference #
• 2J2-83560-00

Swing Arm Bearing set SR500

SR500 1978-81 1982-93, XT500 1976-81

Swing arm bolt Grease Fitting - Replace original grease fittings with ones that
fit to common American size grease guns. Fittings fit to ends of swing arm
shaft (bolt). 2 required per bike. Fits: All 650's 1970-84

Clamp on Air Filter. SR500 1978-83, XT500, XS750 through 1979, XS850 through 1979, XS1100 through 1979

OEM Reference #
• 2J2-14451-00

52mm Universal Clamp on Air Filter

Fits: Yamaha SR500, TT500, XT500, XJ650, XJ900, XS750 & XS850 & XS1100 through 1979

Also fits:
Honda CB400 N/T, CB650 Z, CB750 K
Kawasaki KZ250, KZ400 B/G/L, ZR400, KZ440 A/C/D/H, KZ550 G/H, GPz550, ZR550, KZ650
Suzuki GS400 S, GSX400 E/F/L, GT500, GS550 E/M, GT750

Oil Filter SR500

Also fits: SR250 79-84, SR250 Exciter 80-82, XT250 80-84, XV250 Virago 91-09, SR400, XT400 81-84, XT400 E 91, XV400 Virago 87-94, XVS400 Drag Star/Classic 96-08, XZ400 D81-82, TT500 76-81, XT500 76-83, XV500 Virago 83-84, XV535 Virago 87-02, XZ550 Vision 82-83, SRX600 85-90, TT600 83-92, TT600RE 04, XT600 Z Tenere 83-91, XVS650 02-09, MT03 06-09, SZR660 96-98, XT660 04-09, XTZ660 Tenere 91-99, XV700 Virago 84-87, TDM850 90-01, TRX850 96-00,TDM900 02-08, XV920 Virago 81-83, XV1000 Virago 81-85, BT1100 Bulldog 02-06, XV1100 Virago 86-99, XVS1100 V-Star 99-09

Front Sprocket 16Tx530

SR500 Front, XS500

Also fits Suzuki: GS400 X 77-78, GS425 79, GS450 E 80-83, GS450 L 80-83 & 85, GS450 S 80-81, GS450 T 81-82, GS450 TX 82-83, GS550 77079, GS550 Spoke 80, GS550 ES 83-85, GS550 E MAG 78-80,GS550 L 81-83 & 85 ,GS550 M 82, GS 550 L MAG 79-80, GS550 T 81, GS550 E3S 84, GS550 E 83 & 85, GS700 E/ES 85, GS750 ES, XN85 83.
Suzuki reference OEM 27511-44000

Sprocket 42Tx530 SR500 Rear

OEM Reference #
• 2J4-25442-20

Clutch Disk SR500 1978-84 Sold EACH. The SR500 uses 8 pieces. Also fits: XT500 1976-81 (needs 8), SR250 Exciter 80-83 (only needs 6 plates), XZ550R 82-83 (8), XT600 84-95 (6), XS850 1980-81 (7),

OEM Reference #
• 5Y1-16321-00-00

Clutch Spring Set (6 pcs) SR500 1978-85 Also fits: YZ250 88-98, XT500 1978-88, XV750 81-97, XV920 82-83, XV1000 82-85 The following use 5 of the 6 springs: YZ125 91-11, XT250 09-10, XT350 90-98, XZ550 82, XJ550 83, XJ600 84, XJ600 N 95-02, XJ600 S 92-99, XJ650 80-83, XJ750 81-83, XV750 81-97, XV920 82-83, XV1000 82-85

OEM Reference #
• 90501-16321-00

This product is temporarily out of stock.

Fork Seal set (2)

Fits: RD400 1978-79, SR500 1978-93, XS650 1977-83, TX750 1973-74

Headpipe Exhaust Gaskets - (Pk./2) - Original Yamaha type - Fits: All XS650's 1970-84. OEM Ref.# 256/3GD-14613-00, 90430-38054 Also fits: SR500 E/F/G/G 78-81, XT500 C/D/E/F/H 76-81

OEM Reference #
• 256-14613-00
• 3GD-14613-00
• 90430-38054

GB Cafe Headlight Bracket Set. - Polished Aluminum - 35mm. Fits: 35mm.
fork tubes as used on 1977-84 XS650's. 11mm. mount holes. Approximately 4 1/2 inches from center of fork tube mount hole to center of headlight attachment hole.
Bikes with standard 35mm forks: XS400 Maxim 82-83, SR500 E/F/G/H 78-81, XS500 C/D/E 76-78, XJ550 RH/RJ/RK Seca 81-83, XZ550 RJ/RK Vision 82-83, TX750 A 73-74, XS750.
Please note we find the forks have some times been replaced with different sizes on old bikes.
Yamaha, Suzuki, Kawasaki, Honda.

7" Halogen Lamp Kit - Lamp unit with 12V 60/55 Bulb (P43T base) and bulb dust boot. Replaces stock headlight sealed beam. Fits into stock retainer of 74-84 XS650 & TX 650 headlamp. XS1/XS1B/XS2/TX650 (1970-73) models must use #10-1156 "W" clip set and clip the lamp unit to the headlamp rim. Can be used with XS400, XS750, XS850, XS1100 and SR500 but connectors and wiring harness do not work together. To use you must cut the ends on the lamp and your headlight, match up the correct wires, and then solder and shrink wrap the wires together.

OEM Reference #
• 256-84320-60-00

7" Classic Chromed Steel Headlight Assembly with Halogen Lamp . XS650, TX650, XS750, XS850, XS1100, SR500

OEM Reference #
• 256-84330-00-00

7" Halogen Lamp with 60/55 watt H4 P43T Halogen Bulb and parking light. E-Mark certified for RH drive European Market use (can also be used in north America). Replaces stock headlight sealed beam. Fits into stock retainer of 1974-84 XS650 & TX650 Headlamp. Note: XS1/XS1b/XS2/TX650 (1970-73) models must use #10-1156 "W" Clip Set and clip the lamp unit to the headlamp rim. XS750, XS850, XS1100, SR500 - connector likely will not plug into bike wiring harness, you will have to solder and shrink wrap.

OEM Reference #
• 2F3-84321-A0-00

Original type 7" Headlight assembly as used on all 650's 1974-84. Custom Polished chrome finish with upgrade to H4 Halogen lamp assembly - (U.S.A. market RH side drive) Includes shell, rim, light unit with 60/55W H4 12V P43T bulb, rubber mounting bushes and wiring grommets. XS750, XS850, XS1100, SR500 - will need to solder and heat shrink wiring.

OEM Reference #
• 584-84310-60-00

Turn Signal Lamp with Amber Lens. Fits: front or rear on 1973-84 TX/XS650's. Also fits: XS360, XS400, XS750 78-79, XS850 80-81, XS1100 SF 79-81

OEM Reference #
• 360-83310-70
• 366-83330-70
• 366-83340-70

Rear Short stalk Signal Lamp. For those wanting signal lamps tucked in closer to the frame. 8 mm. stud mount. As used for European Markets. Lens has milky translucent center. DOT approved. E mark. Yamaha XS650. Will work on XS400, XS750. XS850, some SR500.

OEM Reference #
• 533-83340-40

Rear Short stalk Signal Lamp. For those wanting signal lamps tucked in closer to the frame. 8 mm. stud mount. Clear amber lens. Yamaha XS650 and other vintage motorcycles. Will work on XS400, XS750, XS850, some SR500. ** Not DOT approved

OEM Reference #
• 533-83340-40

Rear Medium stalk Signal Lamp. Length from end of stem to inside of lens is 67mm, length from the "step" in the stem is 46mm, total length is 147mm. 8 mm. stud mount. As used for European Markets. Lens has milky
translucent center. DOT approved. E mark.

Yamaha XS650. Will work on XS400, XS750, XS850, some SR500.

Brake Pad set Vesrah performance brand, made in Japan. Vesrah VD-205 Brake Pad Set ( for 1 caliper ) - Fits: Front - XS650 D-K (1977-84) and Rear - XS650 (1978-84 - Resin compound. OEM Ref.: 1J3-20000-11/13, 3H5-W0045-00, 2MO-W0046-01 XS250 C 77, XS250 DE F,G 79-880, XS360 76-77, XS400 E, F 78-79, SR500 76-81, SR500 E/F 78-79 front and rear, SR500 G/H 80-81 front only, SR500 80-90 front, XS500 C/D/E 76-78 front and rear, XJ650 R 82, XS750 D/2D/E/F 77-79 front and rear, XS750 SE/SF right and left rear 78-79, XS850 G/H 80-81 front and rear, XS850 LH/LH/SG/SH right and left rear, XV920 RH/RJ 81-82 front only, XS1100 E/F/G/H 78-81 front and rear, XS1100 SG/SH 80-81 left and right rear, XS1100 LG Midnight right and left rear.

OEM Reference #
• 1J3-20000-11
• 1J3-20000-13
• 3H5-W0045-00
• 2M0-W0046-01

219FTSS x106 Endless Cam Chain. Made in Japan. Endless chain preferred for racing applications. Please note that endless cam chains are not easy to install. Fits: SR500 78-81, XT500 76-81 OEM reference 219FTSSx106 EL

OEM Reference #
• 219FTSSx106
• EL

Cam Chain - Daido 219FTss x 106 with rivet link. Pitch .3061" (7.774mm.)
Fits: TX/XS650's 1974-84 (36 tooth cam). The latest high strength cam chain
from D.I.D. for late XS650's. Made in Japan.
Also fits: SR500 E/F/G/H 78-81, XT500 C/D/E/F/G/H Dual Sport 76-81

Installation Note: Cam Chain IS absolutely correct original brand/size/length/type
Original install will be Very tight as chain is pressure injected with grease at factory
and head gasket is not yet compressed. Install with tensioner assembly out and it may
be necessary to pry chain over last half tooth of cam sprocket to get the chain in place
so joiner link can be installed. Chain will loosen once head is torqued and engine is run
a short time.

Fits: 1978-84 Yamaha XS650 "Specials" Note: Caps from "Standards" and "Specials" do not interchange. Will work with other Specials models: XS400 Specials, XS750 Specials, XS850 Specials, XS1100 Specials, and SR500 OEM reference #306-81862-10-00

OEM Reference #
• 306-81862-10-00

Gas Cap with keys - Fits: 1976-79 XS650 "Standard" models and our 64-7700 and 64-7702 Fuel Tanks. Note: Caps from "Standards" and "Specials" do not interchange. Also fits: RD400 76-80, SR500 78-79, XS750 77-79, XS850 80

OEM Reference #
• 584-24602-00
• 1E7-24602-00

Kit contains o rings and diaphragms to rebuild one fuel petcock. Does not include plastic diaphragm spacer block.

Yamaha XS650 E 78

XS360 C, D, 2D 76-77
XS400 D 77
SR500 E/F/G/H 78-81
SR500 82-84, 88, 91-93
XS500 E 78
XS750 D/2D/E/F 77-79
XS1100 E/F/G/H 78-81

Vesrah Clutch Friction Plate - sold EACH Full set for XS400 is 7 plates/disks. Vesrah # VP-2041. Fits: XV250 P/PC-W1/W1C XV250 G/GC-K/KC Route 66 95-98 XS360 76-77 XS400 D/E/F 77-79 XS4002E/2F 78-79 XS400 G/H Special XS400 SG/SH/SJ Special SR500 E/F/G/H TX500 A FJ600 L/LC/N/NC 84-85 FZ600 S/SC/T/TC/U/UC 86-88 FZ600 SS/SSC/ST/STC FZ600 T/TC/V/VC FZ6 05 XS750 77-80 RD350 and RD400 builders also use these plates.

OEM Reference #
• 4H7-16321-00
• 383-16321-00
• 1J7-16321-00

Vesrah Brake Pads for Mag wheels. Fit the front and rear for many bikes - see list below. Sold per set for front OR rear. Need to buy 2 sets if doing front and rear.

Fits:
XS360 C/D/2D 1976-77 FRONT ONLY
XS400 D/E/F 1977-79 Mag wheels only
SR500 E/F 1978-79
SR500 G/H 1980-81 FRONT ONLY
XS500 C/D/E 1976-78
XJ650 RJ Seca 1982 FRONT ONLY
XS650 D/E/F/2F 1977-79 FRONT ONLY
XS650 G/H Special II 80-81 FRONT ONLY
XS650 Special 1978-80
XS650 SH Special 1981 FRONT ONLY, Mag only
XS650 SJ/SK 1982/83 FRONT ONLY, Mag only
XS750 D/2D/E/F 1977-79
XS750 SE/SF Special 1978-79 REAR ONLY
XS850 G/H 1980-81
XV920 RH/RJ 81-82 FRONT ONLY
XS1100 E/F/G/H 1978-81
XS1100 LG Midnight 1980 REAR ONLY
XS1100 Special 1979-81 REAR ONLY

Brake Caliper Rebuild Kit - Fits:1977-84 XS650 Front or Rear Calipers. Contains caliper piston seal, dust boot, spring clip and bleed screw rubber cap. OEM Ref.# 1J3-W0047, 1J3-20000-20-00 Also fits: XS400 D/E/F 77-79 front and rear, SR500 E/F/G/H 78-81 front and rear, XS500 C/D/E 76-78 front and rear, XS750 77-79 rear only, XS850 S F 79 front and rear, XS850 79-81 rear only, XV1000 1982, XS1100 G Midnight Special 80 rear only, XS1100S F/G 79-80 rear only, XS1100S H 81 rear only.

OEM Reference #
• 1J3-W0047-00
• 1J3-20000-20-00

Rear Brake pads SR500 G/H 80/81. Full metal pad, grooved shoe

Brake Pad Set ( for 1 caliper ) - Fits: Front - XS650 D-K (1977-84) and Rear - XS650 (1978-84) - Kevlar Carbon compound. OEM Ref.: 1J3-20000-11/13, 3H5-W0045-00, 2MO-W0046-01 Also fit: SR500 1976-81, SR500 G/H 1980-81 front only, XS500 C/D/E 1976-78 front and rear, XS750 D/2D/E/F 1977-79 front and rear, XS750 SE/SF right and left rear, XS850 G/H 1980-81 front and rear, XS850 LH/LH/SG/SH right and left rear, XV920 RH/RJ 1981-82 front only, XS1100 E/F/G/H 1978-81 front and rear, XS1100 SG/SH 1980-81 left and right rear, XS1100 LG Midnight right and left rear. Equivalent: Vesrah VD205, EBC FA34

OEM Reference #
• 1J3-20000-11
• 1J3-20000-13
• 3H5-W0045-00
• 2M0-W0046-01
• 4K0-W0045-00
• 1L9-W0046-00
• 2J2-W0046-00
• 3G1-W0046-00
• 3H5-W0045-00
• 1J3-W0046-00
• 1J3-W0045-00
• 1L9-W0045-00
• 1U4-W0046-01/02

Front Brake Master Cylinder Rebuild Kit - OEM # 535-W0041-60, 535-20000-60 Fits: Front Master Cylinder Assembly on All XS650 Models D-L (1977-84) with single front disc brake. Note: This Kit does Not fit earlier 650 models. Also Fits: XS360 C 76-79, XS400 77-81, SR500 78-82, XS500 76-78,

OEM Reference #
• 535-W0041-60-00
• 535-20000-60

Shock Absorber Set - (Monza Traditional) standard size for 1974-84 XS650 TX650's - Dual Progressive
wound Chrome Springs & Long Black top shroud with black shock body.
12 3/4" (324mm.) eye to eye., Includes preload wrench & set of eye rubbers.

Can be used as replacement on: Yamaha RD400 1976-79, XS400 1977-81, SR500 1978-81, XS750 1977-78, XS850 1980-81, XS1100 1979-81, XV700 1984-86, XJ750 1981-83, XJ900 1983, XJ1100 1982, XV1100 1984-86, RD250 1978-79
Eye to eye 325mm is standard size for:
Suzuki GT185 1972-77, GS250 1980-81, GT250 L/M/A/B/C 1973-78, T250 1970-73, T350 1970-73, GT380 1972-77, GS400 1977-78, GT500 1975-77, T500 1971-75, GT550 1972-77, GS650 GLX 1982, VS700 1985-86, GT750 1972-77
Kawasaki KZ200 A1 A2 1978-79, KZ250 D/L/W 1980-83, KH250 1973-76, KZ350 A/B 1981-88, KH400 A3 A4 1975-76, S3 A (400) 1974-75, KZ400 A/B/C/D/S 1974-79, H1 A-F KH500 1969-1976, KZ550 C1-C4 1980-83, KZ650 B/C/D/E/F/H 1977-83, NV700 A1 1985, H2 A/B/C (750) 1972-75, KZ750 B1-B4 1976-79, VN750 A2-A4 1986-88
Honda CX500 C/D 1978-82, VT500FT 1983-84, XBR500 1987-89, CB650 SC 1982-85, VF700 C 1986-87, VT750 C 1983, CB900 C 1980-82, CB1000 C 1983.

Tachometer - Chrome Mini - 2.25" Diameter (60mm) - Black face, 0-12,000 RPM for Yamaha
650's. Internal illumination Halogen Backlit.
Mechanical (cable drive) type. 1:5 ratio.

Other bikes with 1:5 ratio: XS360, XS400, RD350, RD400, SR500

Tachometer - Chrome Mini - 2.25" Diameter (60mm) - White face, 0-12,000 RPM for Yamaha
650's. LED Internal illumination.
Mechanical (cable drive) type. 1:5 ratio.

Other bikes with 1:5 ratio: XS360, XS400, RD350, RD400, SR500

Tachometer - Chrome Mini - 2.25" Diameter (60mm) - LED with Black face, 0-12,000 RPM for
Yamaha 650's. Internal illumination.
Mechanical (cable drive) type. 1:5 ratio.

Other bikes with 1:5 ratio: XS360, XS400, RD350, RD400, SR500

Tachometer - Chrome Mini - 1.9" Diameter (48mm) - White Face, 0-12,000 RPM for Yamaha
650's. Internal illumination.
Mechanical (cable drive) type. 1:5 ratio.

Other bikes with 1:5 ratio: XS360, XS400, RD350, RD400, SR500

see speedo's 03-0751, 03-0753

Tachometer - Chrome Mini - 2.25" Diameter (60mm) - White face, 0-12,000 RPM for Yamaha 650's.
Internal illumination. Mechanical (cable drive) type. 1:5 ratio.

Other bikes with 1:5 ratio: XS360, XS400, RD350, RD400, SR500

IZUMI ES530HSDC x 104 (Heavy Super Duty O-Ring Chain) Superior Quality - Made in Japan This is the stock chain Length for 1974-84 Yamaha XS650's with 17T/34T standard Sprockets. XS360 XS400 SR500 standard size Yamaha, Suzuki, Kawasaki, Honda.

OEM Reference #
• 94580-05104-00

IZUMI Rear Drive Chain - ES530H x 104 Link. This is the stock length on 1974-84 XS650's with 17T/34T standard sprockets. Heavy Duty Motorcycle Chain - Japanese Made Superior Quality XS360 XS400 SR500 standard size Yamaha, Suzuki, Kawasaki, Honda.

OEM Reference #
• 94580-05104-00

IZUMI Rear Drive Chain - 530HT x 104 Link.- Japanese made - Premium Quality This is the stock length on 1974-84 XS650's with 17T/34T standard sprockets. High Tensile Motorcycle Chain with Nickel Plated Sideplates. XS360 XS400 SR500 standard size Yamaha, Suzuki, Kawasaki, Honda.

OEM Reference #
• 94580-05104-00

Clutch Lever - (Black) - Fits: XS650 SE/F/2F/SF/SG/SH/SK/SL 1978-84 and XS650S J/K Heritage Specials. OEM Ref.#'s 2HO-83912-00/20/30, 2H7-83912 Also fits: XS400, SR500 78-81, XS750 F 79, XS850 80-81, XS1100 78-81

OEM Reference #
• 2H0-83912-20
• 2H0-83912-30-00

Brake Lever - (Black) - Fits: XS650 SE/F/2F/SF/SG/SH/SK/SL 1978-84, and XS650S J/K Heritage Specials. Also Fits our 08-0255/0265 Master Cylinders. OEM Ref.#'s 2H7-83922-00, 2H7-83922-20, 2J2-83922-20, 4L0-83922-00 Also fits: XS400 78-81, SR500 78-79, XJ650 Maxim 80-83, XJ650 L 81, XJ650 Seca 82, XS750 78-79, XV750 Virago 81-83, XS850 80-81, XJ1100 82, XS1100 79-81 *** has finger indentions

OEM Reference #
• 2H7-83922-00
• 2H0-83912-30-00

Brake lever (silver) 77-84. With finger indentions.

Also compatible with: XS400 79-81, SR500 78-79, XJ550 Seca 81-83, XJ650 Maxim 80-83, XJ650 L 81, XJ650 R Seca 82, XS750 E/F 78-79, XV750 Virago 81-83, XS850 80-81, XJ1100 82, XS1100 L/S 78-81

08-0134 is matching clutch lever.

*** has finger indentions

Clutch lever (silver) 78-83 with finger indentations.

Also compatible with: XS400 79-81, XS400 S 81, SR500 78-79, XJ550 Seca 81-83, XJ650 L 81, XJ650 Maxim 80-83, XJ650 R Seca 82, XS750 E/F 78-79, XV750 Virago 81-83, XS1100 L/S 78-81.

08-0118 is matching brake lever.

Clutch Cable Adjuster Dust Cover - Rubber boot/cover keeps dirt from contaminating cable adjuster threads. Replaces original OEM cover. Fits: 1978-84 XS650's and hundreds of other Yamaha's.

OEM Reference #
• 1E6-26342-00

H 1.85x19 36 hole shouldered polished aluminum rim. Very hard to find. Classic 36 hole pattern will work with many vintage bikes. Works with XS650. This is a quality rim comparable to what you see on other sites for much more money. Great for chopper, bobber projects. OEM reference # 94418-19145-00 given for replacement reference only, the materials and specifications are different, this is not an OEM rim. This is the standard size front rim for SR500 for those looking to convert from mag wheels.

OEM Reference #
• 94418-19145-00
• (for-reference-only)

Alloy Bracket - For Fork tube end of our Hydraulic Steering Damper.
Fits: 35mm. Fork tubes on Yamaha XS650's (1977-84). Made in Japan
Bikes with standard 35mm forks: XS400 Maxim 82-83, SR500 E/F/G/H 78-81, XS500 C/D/E 76-78, XJ550 RH/RJ/RK Seca 81-83, XZ550 RJ/RK Vision 82-83, TX750 A 73-74, XS750.

Will work with Yamaha 35mm forks, including standard SR500, RD400 1979.

Valve Stem Seals (Sold each) - Fits: All 650's 1970-84 Made in Japan - OEM Ref.# 341-12119-00/02 Also fits: SR500 78-81, SR500 82-88, XT500 88, XT500 76-81, TT500 76-81, XV750 82, XV920 82-83, XV1000 83, XV750 81-83, XV1000 84-85, XV920 81-82, XV1000 82, XV920 83

OEM Reference #
• 341-12119-00
• 341-12119-02
• 341-12119-02-00

Great battery for your custom cafe racer and bobber projects. Much smaller and lighter than lead acid batteries, comes with packing to fit the battery box. The manufacturer expects Li-on batteries to last on average about twice as long as a lead acid battery in the same application, making the effective cost differential much lower.

• 134mm length.
• Ultra light - on average 1/5 the weight of lead acid batteries. Save about 6.5 pounds compared to YTX14AHL-BS. Weighs 2.28 lbs (1032 grams).
• Zero sulfation for longer service life.
• Holds unloaded charge for one year without maintenance, great for motorcycles put up for the winter. Generally there is no need for tender.
• No explosive gasses during charge, no lead, no acid.
• Two year warranty from Shorai.
• 12V. Max Charge 14 Amps.
• It is important that the equipment on your bike does not over charge this battery to preserve its longevity.

Battery User Manual (PDF)