Mikes XS

Plastic Side Cover Set/2 - Black Finish
Fits: 1980-84 XS650 "Specials" with stock plastic sidecovers.
Sold in Sets Only! Emblems available separate. Each sidecover Set includes
new mounting rubbers. Our sidecovers are exact in shape to originals but come
undrilled so that badge mounting is optional. The rear of the sidecovers are
dimpled in the correct original badge hole locations so that they can be drilled
for badge mount holes if desired.

Plastic Side Cover Set/2 - Chrome Finish
Fits: 1980-84 XS650 "Specials" with stock plastic sidecovers.
Sold in Sets Only! Emblems available separate. Each sidecover Set includes
new mounting rubbers. Our sidecovers are exact in shape to originals but come
undrilled so that badge mounting is optional. The rear of the sidecovers are
dimpled in the correct original badge hole locations so that they can be drilled
for badge mount holes if desired.

Sidecover Emblem Set (3G1)- Gold- for 1980
XS650SG but also fits to all 78-81 "Specials"


Note: This set is 2pc. of RH Sidecover badges. These fit to both sidecovers
and the difference (Checkmark) is not usually noticeable unless they are
installed on old paint.

Sidecover Emblem Set (4M4) - Gold - for 1981
XS650SH but also fits to all 78-81 "Specials"

Sidecover Emblem Set - "Heritage Specials" (3NO)- stock adhesive mount back.

Damper Rubber (2Pc. Set for 1 sidecover) Fits: To 1 3/8" wide upper hanger for
Metal side cover as used on XS/TX650 1974-79 "Standard" models. See web
site model ID photo's of sidecovers if you are unsure of your sidecover type.

Damper Rubbers (Pk./2 for 1 sidecover) Fits: To 1" wide upper hanger for Metal
side cover as used on XS650Se/Sf/2F/G 1978-80. See web site model ID photo's
of sidecovers if you are unsure of your sidecover type.

Knob/Latch assembly for Metal side covers used on 1974-80 Models. Includes
knob, Spring, rubber grommet, roll pin and special washers.

Damper Grommet for sidecover (Upper - Pk./2 for 1 sidecover) - Fits:XS650SG-
SL (1980-84) "Specials" with plastic sidecovers. See web site model ID photo's
of sidecovers if you are unsure of your sidecover type.

Damper Grommet for sidecover - (Lower single piece for 1 sidecover
fits into frame tube). Fits: Plastic covers as used on XS650SG-SL
plus H Special II 1980-84 "Specials". See web site model ID photo's
if you are unsure of your sidecover type.

Gas Tank Mount Rubber - Front - Fits: All 650's 1970-84

Gas Tank Mount Rubber - Rear - Fits: All 650's 1970-84

Battery Box Mount rubbers (4 Pc. set). Fits: All 650's 1970-84

Battery Boot - Fits: 12N14 type Batteries as used on 1974-84 Yamaha 650's.

Battery Retainer Strap - As used on XS/TX 650's (1974-84)

Battery Retainer Strap - As used on XS2/TX650 (1972-73)

Damper Rubber - Rear Fender/Grab Rail mounting bolt
through point - Set of 2 As used on 74-79 "Standard"
Models OEM Ref. #168-21639-00-00

Shoulder Bolts - Replacement for Stock Rear Fender
Mounting Bolts as used on 74-79 "Standard" models
(these Bolts pass thru the stock rear fender, the
rear fender mount rubbers and into the grab rail
mount). Bolts also are replacements for the bolts
included with grab rail #68-6809.

Rubber Grommet with metal bushing - Fits: Sidecover latch , Headlamp adjuster,
Mount - lower (plastic section) of Rear fender, Front mount point of chain guard,
Tail lamp base to fender (round tail lens), Rear master cylinder reservoir mount
(1978-80 ) OEM Ref.#'s 214-21717-00 / 90480-14101/102-00/14023-00 + collar
90387-07390-00/0714B-00

Front fender Speedo cable loop.
Fits: Stock fender on all 1977-84 XS650's

Damper Rubbers - (Rider footrest mount bracket) - Set of 4 - Fits: All 1970-84
XS/TX650's

Polished Chrome Shock Crown Nut - Short Type
17mm hex x 10mm 1.25pitch x 16mm Long
Fits: All Footrest mount bars 70-84 + Fender mount thru point on 76-78's.

Chrome Thick Washer - 10mm. x 27mm. x 4.5mm. - Fits: All Footrest mount
bars on 1970-84 650's and shock absorber top mount stud on 1974-79 650's.

Rider Footrest Rubber - Flat Bottom type - Fits: 1977-84 650's
Sold each.

Rider Footrest Rubber - Rounded Bottom type - Fits:1970-76 XS/TX650's

Passenger Peg Set - (1LH + 1RH) with mount brackets (original type).
Fits: 650's 1977-84

Kickstart Rubber - Fits: Small 13mm. shaft (later type kick start levers) as
shown.

Kickstart Rubber - Fits: Large 15mm. shaft (early straight type kick start lever).

Kickstart Rebuild Kit - Fits: Early straight type lever. Kit Contains: Spring - 90501-
15091, Special Washer - 90201-17256, circlip 93430-12022, 5/16 Ball Bearing
93505-16006 .

Handlebar damper rubbers (Set of 4) - Fits into Top crown & dampens vibration.

Signal Mount Kit - Fits: Front Signals on all 1974-84 XS/TX650's - Kit Replaces
worn & distorted original mounts, cures drooping & loose signal mounts. Kit
includes 4 pc.as shown ( for 1 Signal ). Sold as a kit only !

Signal Mount Kit - Fits: Rear Signals on all 1974-84 XS/TX650's - Kit Replaces
worn & distorted original mounts, cures drooping & loose signal mounts. Kit
includes 3 pc.as shown ( for 1 Signal ). Sold as a kit only !

Center Stand Stop Rubber fits to stock muffler on 1970-73 XS/TX 650's

Rubber Bumper - OEM original Stand stop Rubber - Also for use with aftermarket
muffler center stand stops. 1" Dia x 9/16" Long - Fits into 3/8" (10mm) Hole
OEM Ref. # 278-27114-00/01/A0, 371-27114-00-00
Used on All TX/XS650's 1974-84 - (Some models use 2 pc.)
Rubber bumper is mounted to muffler and/or frame.

Metal center stand stop bracket. Black - 3 5/8" long with oblong mount hole
(mounts to passenger peg stud). This bracket is used with rubber center stand
bumper listed above to prevent metal to metal contact between center stand and
exhaust systems

Metal center stand stop bracket. Black - 4 5/8" long with oblong mount hole.

Metal center stand stop bracket. Black - 6 1/4"" long with oblong mount hole.