Mikes XS

LED Charging system indicator Gauge. Shows Voltage of your alternator rising and
falling with RPM and gives a clear indication of your charging systems normal
operation and early warning of problems.
Gauge is Bright High Quality Chrome plated and clamps onto 7/8" Bars and can be
easily wired into any point in the system (before a switched load is best). Can be
mounted as shown or to handlebar by clamp (included).
Handlebar top clamp, which is also shown is not included.

Fits: All 650's 1970-84

Great battery for your custom cafe racer and bobber projects. Much smaller and lighter than lead acid batteries, comes with packing to fit the battery box. The manufacturer expects Li-on batteries to last on average about twice as long as a lead acid battery in the same application, making the effective cost differential much lower.

• 134mm length.
• Ultra light - on average 1/5 the weight of lead acid batteries. Save about 6.5 pounds compared to YTX14AHL-BS. Weighs 2.28 lbs (1032 grams).
• Zero sulfation for longer service life.
• Holds unloaded charge for one year without maintenance, great for motorcycles put up for the winter. Generally there is no need for tender.
• No explosive gasses during charge, no lead, no acid.
• Two year warranty from Shorai.
• 12V. Max Charge 14 Amps.
• It is important that the equipment on your bike does not over charge this battery to preserve its longevity.

Battery User Manual (PDF)

AGM Battery - Fits: 1974-84 XS650's

XS750, XS850

CBTX14AHL-BS AGM Battery - XS# 61-2020
Absorbed Glass Mat(AGM) is the latest in motorcycle battery technology.
Sealed AGM batteries completely eliminate the hassles of conventional
battery maintenance. There is no liquid acid in the AGM battery. All of the
acid is absorbed into the compressed glass matting in the cells. They are
completely Non-Spillable, so they can be shipped by U.S. Mail or UPS with
no hazardous warnings or extra fees. They can be mounted in any position
for special applications. Our AGM batteries re-combine the oxygen and
hydrogen as the batteries charge and discharge to make them truly
maintenance free. No liquid ever needs to be added, No leaks, spills or vent
tubes. AGM batteries have higher cold cranking Amps and hold a charge
much longer. Replaces 12n14-3a / YB14LA2 original batteries

AGM Batteries Feature
Batteries are wet charged at the factory but contain no liquid acid.
Absorbed Glass Mat (AGM) technology eliminates the need to add electrolyte.
Built to withstand the demands of high-heat applications.
Lower internal resistance reduces charging time vs. conventional wet batteries.
Permaseal Design is Maintenance Free and Non-Spillable.
Resistant to vibration damage for reliable performance even under
rough off-road conditions.
Engineered to meet or exceed OEM specifications to ensure exact fit and power needs.
Slower self discharge rate means AGM batteries can sit for extended periods
of time without constant monitoring. A conventional wet battery discharges
15% a month where our AGM batteries discharge only 2-3% a month.

AGM Battery - Fits: XS2/TX650's 1972-1973
Replaces original 12n12a-4a-1
This high power version never existed before and was made in the sealed
maintenance free AGM type for Mikes XS. It will bring more power and durability
to your old early 650 electrical system.
170cca, 12volt AGM type (actual peak voltage 14.5 volts).
Dimensions - 5 5/16" Long x 3 3/16" wide x 6 5/16" high
Fits XS400 battery box, post connections may be different than stock so take care to hook up the + and - connections properly.

Fully activated and ready to use!

Battery Boot - Fits: 12N14 type Batteries as used on 1974-84 Yamaha 650's.

OEM Reference #
• 447-82122-00

Battery Retainer Strap - As used on XS/TX 650's (1974-84)

OEM Reference #
• 120-82131-00

Battery Retainer Strap - As used on XS2 TX650 (1972-73)

OEM Reference #
• 306-82124
• 256-82124-00-00

Battery top cover - Fits: 1978-84 XS650 "Specials".

OEM Reference #
• 2MO-82129-00
• 2M0-82129-00-00

Electrical Continuity Tester (use with power off) - Detects open circuit in fuses,
diodes, switches, sockets and wires (requires one AA battery - Not included).
Long 48" leads.

Deluxe 12 Volt Battery Charger for AGM (Absorbed glass mat), Maintenance free,
VRLA, Gel and conventional flooded lead acid batteries. UL & CSA Approved.
Output is 1.25 Amps, 12 volt DC (maximum 14.5 Volts). 4 Stage Microprocessor
controlled charging with automatic shutoff at full charge. 120v AC Input.

1. Qualification - Ensures battery is safe to charge, and has minimum 3 Volts.
2. Bulk Charge - Raises battery to 80 percent of full voltage.
3. Absorption - Holds battery voltage at 80 percent and forces current to top battery
4. Float Mode - Maintains the fully charged battery at a proper working voltage.
Charger Features - 6 LED indicators to show charging status, reverse polarity
protection, overheat protection, overcharge protection and spark proofing.
Full instructions, quick disconnect alligator clip leads and fused eye terminal
leads included. (Not for outdoor use).

Battery Charger (6V-12V). Half Amp charge rate with R-connection Input plug that secures to the battery. Just plug in charger output plug to charge the battery. No mess, no need to remove the battery every time you charge it. On/Off switch with power indicator light assures safe operation. For North American market.

Electric Circuit Tester - Checks all motorcycle primary electrical and computer
circuits for power. Plastic handle lights up if circuit is good. Icepick type
probe and 48" cable with insulated alligator clips.

XS650 Fuse Boxes located on top of the battery are a part of the original wiring
harness and have Not been available separate. We now offer a copy of this
box as shown plus matching terminal block & terminals + the battery top cover
it attaches to. Cut the old fuse box from your main harness, attach the
connector block provided and plug in the new fuse box. Fits: All "Specials"
1978-84. Includes 25mm fuses.
Contains: 10A ignition, 10A signal, 10A Headlight, 20A Main fuses.
Can also be used with RD250, RD350, RZ350, RD400, XS750, XS1100 and XJ650, XJ750, XJ900s. Make sure you verify your wiring to the correct fuse via the connector block. The length of the harness is 2.5 inches, please verify that the wires on your bike are long enough to reach. For the XS850 and XS1100 the fuse box is part of the bike wiring harness, so some adaptation might be required. The same for the RD250 and RD350.

Fuse Holder with space for spare fuse( 30mm.) Correct terminals (both have male ends) to replace fuse holder as used on all 1970-79 "Standard" XS650 models. Comes with 20 amp fuse. R5, DS7, RD250, RD350, RD400

OEM Reference #
• 164-82150
• 1E2-82150

Pk/5 fuses - 25mm.(1 inch) Glass Fuse - 7 Amp.- Fits: 1978-84 "Specials".

Pk/5 fuses - 25mm.(1 inch) Glass Fuse - 10 Amp.- Fits: 1978-84 "Specials".

Pk/5 fuses - 25mm.(1 inch) Glass Fuse - 15 Amp.- Fits: 1978-84 "Specials".

Pk/5 fuses - 25mm.(1 inch) Glass Fuse - 20 Amp.- Fits: 1978-84 "Specials".

Pack/5 fuses - 30mm.(1.2 inch) Glass Fuse - 10 Amp.

Pack/5 fuses - 30mm.(1.2 inch) Glass Fuse - 15 Amp.

Pack/5 fuses - 30mm.(1.2 inch) Glass Fuse - 20 Amp.

Mini Plug Fuse- 5 amp - Pk/5 fuses

Mini Plug Fuse, 7 AMP. Pk/5 fuses

Mini Plug Fuse- 10 amp - Pk/5 fuses

Mini Plug Fuse- 15 amp - Pk/5 fuses

Mini Plug Fuse- 20 amp - Pk/5 fuses

100 Amp Battery Cables (8' Long) with alligator clips - For Motorcycle use.

This product is temporarily out of stock.

Battery Positive (+) Cable - Fits: XS2 (1972), TX650 (1973).
Approximately 6.5" long.

Cable - Battery relay to starter motor on XS2/TX650 1972-73

OEM Reference #
• 306-82116-00
• 256-81615-00-00

Battery Negative (-) Cable to engine block. - Fits: XS2 (1972), TX650 (1973).
Approximately 17" long.

This product is temporarily out of stock.

Battery Positive (+) Cable - Fits: 1974-84 650's. Approximately 7" long.

OEM Reference #
• 447-82115-001

Currently unavailable.

Battery Negative (-) Cable - Frame to negative battery terminal. Fits:74-84 650's. Approximately 6.5" long.

OEM Reference #
• 447-82116-00

Currently unavailable.

Cable - Battery relay to starter motor - Fits: 1974-84 650's.
Approximately 21" long.

Replacement Rubber Cap for starter motor power cable terminal. Fits: All 650's 1972-84.

OEM Reference #
• 306-81862-10-00