Scroll down to see the products
- Drive Chain
- Sprockets
- Discs 77-84
- Gear Levers, Kickstarters, Passenger Pegs, Footrests
- Parts - Brake Calipers 72-76
- OEM Type Rear Brake Parts - (70-84) Models
- Brake Calipers 77-84
- Brake Switches
- OEM Type Brake Hoses, Front Brake Parts for Early (72-76) Models
- Hoses (77-84) Models - Rubber, Stainless
- Front Master Cylinders & Parts
- Custom Rear Master Cylinders
- Handlebars
- Handlebar Grips
- Handlebar Switches
- Cables - Throttle
- Cables - Clutch, Brake, Decompressor, Clutch Brackets
- Cables - Speedometer, Tachometer
- Bar Lever Brackets, Bar Levers
- Wheel Bearings, Wheel Seals, Axels
- Wheel Rims/ Spokes
- Wheel Weights, Tools, Tubes, Rim Strips
- Body Parts - Fenders, Emblems, Side Covers, Gas Tanks, Chain Guards, Rubber mounts
- Rubber Mounts, Rubber Dampers, Rubber Parts, Sidecovers & Sidecover Emblems
- Sidestand / Centerstand Parts
- Seats & Seat Accessories
Brake Caliper Hose Manifold
Brake Hose Manifold for Dual Disc Brakes.
Original Yamaha type manifold with mounting hardware and Banjo Bolts(2).
Lower banjo bolt is the long type for fitting the dual hoses to the calipers.
Hose Sealing Washers also included.
Original Yamaha type manifold with mounting hardware and Banjo Bolts(2).
Lower banjo bolt is the long type for fitting the dual hoses to the calipers.
Hose Sealing Washers also included.
Brake Hose
Brake Hose - Upper Front. Original rubber type with protective spring.
Fits: 1977 Standard models and 1978-84 Specials (With non-stock lower bars).
- Made in Japan - DOT Approved
Fits: 1977 Standard models and 1978-84 Specials (With non-stock lower bars).
- Made in Japan - DOT Approved
Brake hose with 1 rotated fitting
Brake Hose - Upper Front stock type but with one end fitting rotated 180
rotated 180 degrees. Fits: 1977-84 XS650 "Standards" and 1978-84
"Specials" with low bar. Fits better to aftermarket master cylinders
with hose mounted to reservoir front face rather than the stock position
(reservoir end) - D.O.T. Approved - Original Equipment rubber type with
protective spring - Made in Japan.
rotated 180 degrees. Fits: 1977-84 XS650 "Standards" and 1978-84
"Specials" with low bar. Fits better to aftermarket master cylinders
with hose mounted to reservoir front face rather than the stock position
(reservoir end) - D.O.T. Approved - Original Equipment rubber type with
protective spring - Made in Japan.
Brake Hose
Brake Hose - Upper Front. Fits:1978-84. XS650 "Specials" and 77 standards
with non stock high bars - D.O.T. Approved - Original Equipment rubber type
with protective spring - Made in Japan.
with non stock high bars - D.O.T. Approved - Original Equipment rubber type
with protective spring - Made in Japan.
Brake Hose with 1 rotated fitting
Brake Hose - Upper Front stock type but with one end fitting
rotated 180 degrees. Fits: 1978-84 XS650 "Specials" and 77-84
"Standards" with non stock high bars.Fits better to aftermarket
master cylinders with hose mounted to reservoir front face
rather than the stock position (reservoir end) - D.O.T. Approved
-Original Equipment rubber type with protective spring - Made in
Japan.
rotated 180 degrees. Fits: 1978-84 XS650 "Specials" and 77-84
"Standards" with non stock high bars.Fits better to aftermarket
master cylinders with hose mounted to reservoir front face
rather than the stock position (reservoir end) - D.O.T. Approved
-Original Equipment rubber type with protective spring - Made in
Japan.
Brake Hose
Brake Hose - Lower Front. Fits:1977-84650's - Original Equipment rubber type
- Made in Japan - D.O.T. Approved
- Made in Japan - D.O.T. Approved
Brake Hose
+2 " Brake Hose - Lower Front. Fits: European Model 1977-84 650's (calipers are
mounted lower on the fork legs than North American models).
Also may be used for 77-84 North American models with +2" Extended fork tubes.
- Original Equipment rubber type - Made in Japan - D.O.T. Approved
mounted lower on the fork legs than North American models).
Also may be used for 77-84 North American models with +2" Extended fork tubes.
- Original Equipment rubber type - Made in Japan - D.O.T. Approved
Brake Hose
Brake Hose - Rear. Fits: Rear on XS650SE/SF/SG (1978-80) "Specials"
Original Equipment rubber type - Made in Japan. - D.O.T. Approved
Original Equipment rubber type - Made in Japan. - D.O.T. Approved
Braided Stainless Brake Hose
DOT/TUV approved Stainless Steel Braided Brake Line
Fits: 77-84 XS650 Standard models (low bar) Upper Front
approximately 17" Long. Ends rotate up to 1 full turn.
Fits: 77-84 XS650 Standard models (low bar) Upper Front
approximately 17" Long. Ends rotate up to 1 full turn.
Braided Stainless Brake Hose
DOT/TUV approved Stainless Steel Braided Brake Line
Fits: 77-84 XS650 "Special" models (high bar) Upper Front
approximately 20" Long. Ends rotate up to 1 full turn.
Fits: 77-84 XS650 "Special" models (high bar) Upper Front
approximately 20" Long. Ends rotate up to 1 full turn.
Braided Stainless Brake Hose
DOT/TUV approved Stainless Steel Braided Brake Line
Fits: 77-84 XS650 Lower Front approximately 20" Long.
Ends rotate up to 1 full turn.
Fits: 77-84 XS650 Lower Front approximately 20" Long.
Ends rotate up to 1 full turn.
Braided Stainless Brake Hose
DOT/TUV approved Stainless Steel Braided Brake Line
Fits: 78-80 XS650 Rear Disc Brake approximately 24.5" Long.
Ends rotate up to 1 full turn.
Fits: 78-80 XS650 Rear Disc Brake approximately 24.5" Long.
Ends rotate up to 1 full turn.
Braided Stainless Brake Hose
DOT/TUV approved Stainless Steel Braided Brake Line
One Piece Upper/Lower Hose (41" Long) Fits: 77-84 XS650's
Measure! Ends rotate up to 1 full turn.
One Piece Upper/Lower Hose (41" Long) Fits: 77-84 XS650's
Measure! Ends rotate up to 1 full turn.
Banjo Bolt
Banjo Bolt - M10. x 1.25 - Fits: All original XS/TX650 front & rear master cylinders
and most Yamaha brake calipers. - Oem Ref.# 90401-10034
and most Yamaha brake calipers. - Oem Ref.# 90401-10034
Banjo Bolt Washers
Banjo Bolt Washers - 10mm. (Pk./2) Fits: All Brake hoses & Banjo Bolts.
Long (Dual hose) Banjo Bolt
Long Dual hose Banjo Bolt. M10. x 1.25
Hydraulic Banjo Bolt Brake Switch
Brake Switch - Hydraulic Banjo Bolt Type . 10mm. x M1.25 with 24" Lead.
Fits: All Hydraulic Brake systems on all 72-84 XS650's that use a single hose
type banjo bolt. Brake switch bolt can be fitted anywhere from the master
cylinder to the caliper and is actuated by hydraulic pressure.
Fits: All Hydraulic Brake systems on all 72-84 XS650's that use a single hose
type banjo bolt. Brake switch bolt can be fitted anywhere from the master
cylinder to the caliper and is actuated by hydraulic pressure.
Hydraulic Banjo Bolt Brake Switch
Brake Switch - Hydraulic Banjo Bolt Type . 10mm. x M1.00 with 24" Lead.
Fits: All Magura Master Cylinders, Our # 08-4000 rear master cylinder and many
European and Suzuki brake systems (10mm. X M1.00 thread). Must use a single
hose type banjo bolt. Brake switch bolt can be fitted anywhere from the master
cylinder to the caliper and is actuated by hydraulic pressure.
Fits: All Magura Master Cylinders, Our # 08-4000 rear master cylinder and many
European and Suzuki brake systems (10mm. X M1.00 thread). Must use a single
hose type banjo bolt. Brake switch bolt can be fitted anywhere from the master
cylinder to the caliper and is actuated by hydraulic pressure.